Design servomotor for conveyor system
186 viewsDOI:
https://doi.org/10.54939/1859-1043.j.mst.82.2022.81-90Keywords:
Servo motor; Performance; Motor design; Optimization; Conveyor belt application.Abstract
This paper presents a research for calculation, design and performance optimization of servo motor applied in conveyor belt. Firstly, base on the movement requirements of the conveyor, the characteristic requirements of the research engine are determined after detailed calculation steps. Then, the study uses optimization algorithms to find voltage and slip coefficients to optimize the performance at the working points of the motor. This work has reviewed and designed three motors with different configurations and current densities, through which the mass, efficiency and temperature rise can be evaluated and compared. The paper reviewed and designed three motors with different configurations and current densities. The mass, efficiency and temperature rise of these configurations can be evaluated and compared. The optimal design result of servo motor plays a role important in selecting the most suitable motor in terms of cost, performance and response time for a particular demanding application.
References
[1]. Fitouri, M., BenSalem, Y., & Abdelkrim, M. N., “Analysis and co-simulation of permanent magnet synchronous motor with short-circuit fault by finite element method”, 2016 13th International Multi-Conference on Systems, Signals & Devices (SSD), (2016). DOI: https://doi.org/10.1109/SSD.2016.7473721
[2]. M. Centner, “Basics and application of motor design optimization in an industrial environment”, 21th International Conference on, Electrical Machines (ICEM), in Berlin, Germany, pp. 1008-1012, (2014). DOI: https://doi.org/10.1109/ICELMACH.2014.6960304
[3]. S. Stipetic, W. Miebach, D. Zarko, “Optimization in design of electric machines: Methodology and workflow”, Aegean Conference on Electrical Machines and Power Electronics and Advanced Electromechanical Motion Systems (ACEMP-OPTIMELECTROMOTION), Side, Turkey, pp 441-448, (2015). DOI: https://doi.org/10.1109/OPTIM.2015.7427030
[4]. Damir Zarko, Drago Ban, Davor Gooricki, “Improvement of a servomotor design including optimization and cost analysis”, 12th International conference on Power Electronics and Motion Control Conference (EPE-PEMC), in Portoroz, Slovenia, pp. 302-307, (2006). DOI: https://doi.org/10.1109/EPEPEMC.2006.283097
[5]. Mehmet Çunkaşa, Ramazan Akkayab, “Design optimization of induction motor by genetic algorithm and comparison with existing motor”, Mathematical and Computational Applications, Vol. 11, No. 3, pp. 193-203, (2006). DOI: https://doi.org/10.3390/mca11020193
[6]. Li, S., & Yang, M. “Particle swarm optimization combined with finite element method for design of ultrasonic motors”, Sensors and Actuators A: Physical, 148(1), pp. 285–289, (2008). DOI: https://doi.org/10.1016/j.sna.2008.08.004
[7]. Akundi, S. V. K., Simpson, T. W., & Reed, P. M, “Multi-objective design optimization for product platform and product family design using genetic algorithms”, 31st Design Automation Conference, Vol 2, (2005). DOI: https://doi.org/10.1115/DETC2005-84905
[8]. Wu, S., Yu, B., Jiao, Z., Shang, Y., & Luk, P, “Preliminary design and multi-objective optimization of electro - hydrostatic actuator”, Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 231(7), pp. 1258-1268, (2016). DOI: https://doi.org/10.1177/0954410016654181
[9]. A. Messac, A. Ismail-Yahaya, “The normalized normal constraint method for generating the Pareto frontier”, Struct. Multidiscipl. Optim, Vol 25, pp. 86-98, (2003). DOI: https://doi.org/10.1007/s00158-002-0276-1
[10]. R.T. Marler, “Survey of multi-objective optimization methods for engineering”, Struct. Multidiscp. Optim., Vol 26, pp. 369-395, (2004). DOI: https://doi.org/10.1007/s00158-003-0368-6
[11]. Andersson S, “Optimization Servo Motor for Industrial Robot Application”, Lund University, Sweden, (2000).
[12]. Vu Tran Tuan, Sangkla Kreuawan, Pakasit Somsiri, Kanokvate Tungpimolrut, Phuong Nguyen Huy, “Switched reluctance motor and induction machine for e-scooter based on driving cycles design comparisons”, IEEJ Transactions electrical and Electronic Engineering, Vol 15, pp. 931-938, (2020). DOI: https://doi.org/10.1002/tee.23136
[13]. Nguyen Duc Bac, Tran Tuan Vu, Nguyen The Cong, “Multi-target optimal design of servo motors by --constraint algorithm”, Journal of Science & Technology, Hanoi University of Industry, Vol 56, Issue 6, pp. 26-30, (2020). (In Vietnamese).
[14]. SEW Euro Drive, Servo Technology – Drive Engineering and Practical Implementation, Edition 2006, pp. 115-120, (2006).
